StonehengeUS
StonehengeUS Polyxsand polymeric sand natural
natural sand puck

PolyXsand Polymeric Sand – Natural

Don’t settle for polymeric sand that keeps letting you down. Stop risking costly mistakes and performance issues. Choose trusted, American made PolyXsand from StonehengeUS. When quality and consistency are important, PolyXsand is the professional hardscape contractor’s number one polymeric sand choice

Category:
LEARN MORE

For Interlocking Concrete Pavers, Natural Stone Pavers, Wet Cast Pavers, Porcelain Tiles, Clay Pavers

Superior Strength
Haze Free – Guaranteed
Long Lasting Durability

PolyXsand delivers superior strength and long-term durability, not gimmicky claims and false promises. PolyXsand time-tested, original formula provides reliable, haze free performance and is never tricky to install. For hardscape projects that matter, PolyXsand is the only choice that delivers solid performance and value. Your reputation is on the line with every job you build so don’t compromise on your polymeric sand.

PolyXsand prevent sand erosion from the pavement joints caused by rain and other water run-off, deters weed growth and insect infestation plus reduces overall pavement maintenance. PolyXsand is designed to expand and contract during freeze/thaw cycles and remain flexible to resist cracking.

EasySweep Logo
DATA & SDS SHEET

PolyXsand Polymeric Sand – Natural

StonehengeUS Polyxsand polymeric sand natural
platinum sand puck
natural sand puck

Installation Conditions:

  • Prior to installation of PolyXsand, make sure pavement joints and surface are completely dry AND there is no rain forecasted for at least 12 hours after installation. PolyXsand needs to surpass the set up threshold before getting rained on. If there is a possibility of rain shortly after installation, cover project with a tarp. Remove tarp as soon as threat of rain is gone.
  • PolyXsand should be installed when the average ambient air temperature is above 35 degrees for a minimum of 48 hours after installation.
  • Always wear personal protection equipment: eyewear and respirator.
  • PolyXsand is designed to work best when following ICPI recommended best practices for base installation. Concrete pavers, slabs and natural stone should have ¾” modified stone base and concrete sand setting bed that conforms to ASTM-C33. See instructions below when using PolyXsand on a concrete overlay.

Installation Instructions:

  • Distribute PolyXsand evenly across surface. Sweep sand into joints until full, being careful not to push product over long distances on the surface. (1.5” min depth when using PolyXsand, 1.25” min depth when using X-Treme Wide Joint). After joints are filled, sweep excess product from the surface.
  • For Concrete Pavers: Run vibratory compactor over the pavement to allow the vibrations to consolidate sand particles into the joints and reduce voids. For Cast Stone or Natural Stone: Use a vibratory rubber roller tamper or a rubber hammer and a piece of wood (2” x 4”).
  • Sweep additional sand into the joints if necessary so that the height of the sand is approximately 1/8” below the pavement surface. (Do not overfill joints.) Remove excess product from the surface. Repeat compaction.
  • After joints are filled, sweep surface with broom and then use a leaf blower held on slight angle but close to parallel to surface to remove any excess sand/dust from the top of surface. Take care not to remove any sand from joints.
  • Using a hose, gently mist the pavement no greater than 500 sf at a time. Allow water to absorb for approximately 5 minutes and repeat misting process three to four times, each time gradually adding more volume of water. The last watering should be a volume of water sufficient enough to rinse off any residual material from the surface.
  • In one of the joints, check the moisture depth in the sand with a screwdriver to see that it has penetrated to at least 1½” for pavers and 1 ¼” for natural stone. Replace sand and only apply additional misting if water hasn’t penetrated at least 1½” for pavers and 1 ¼” for natural stone. For optimal joint performance, be certain the entire sand column is fully saturated
  • Any residual surface water caught in the texture of the pavers or natural stone should be blown off the surface with a leaf blower.

Concrete Overlay Additional Instructions:

When using PolyXsand on concrete overlays (pavers/stones installed directly on concrete), a minimum of 1% slope to the concrete and a 1” layer of bedding sand on top of concrete is required. Do not allow water to be trapped in the system. Any water that enters the surface of concrete overlay applications must be allowed to escape the sand setting bed at the outside perimeter of the project. If pavers or stone are set directly on top of the concrete, drill 1” drainage holes thru the concrete with a coverage rate of 1 hole/sq. ft. Fill holes with open graded gravel and covered with geotextile (to keep polymeric sand from migrating into the holes). Drainage channels in lieu of holes in the concrete can also be installed. See ICPI for installation details.

Curing:

PolyXsand contains no portland cement. The curing process varies and could take up to 24 hours based on temperature and humidity level. Cool, damp and overcast conditions will increase PolyXsand set up time.

Storage:

PolyXsand MUST BE STORED in a dry location protected from rain and moisture. Intact, covered pallets can be stored outdoors.

Caution:

  • Do not apply too much water too fast as to flood the pavement or erode sand from paver joints.
  • Prior to applying PolyXsand with natural stone, be sure the surface is free of any dust or stone residue by rinsing thoroughly with water. Then, make sure the natural stone and joints are completely dry prior to installing polymeric sand.
  • Do not apply this product to any wet or damp surface because the polymeric sand will adhere to the surface and is difficult to remove.
  • This product is not designed for vertical applications and is not a substitute for mortar on vertical or horizontal applications.
  • Do not mix or dilute polymeric sand with any other product.

StonehengeUS PolyXSand Products

View our full collection of PolyXsand

 Why StonehengeUS PolyXsand?

Quality

All StonehengeUS PolyXsands are uniformly blended and undergo frequent quality control testing to ensure consistent conformity to all governing standards.

Support

Got questions? Our support team is ready to help you get the answers you need